What Is an Agitated Nutsche Filter Dryer?
An agitated nutsche filter dryer - usually shortened to ANFD, and also called a three-in-one filter dryer - is a single enclosed vessel that performs filtration, cake washing and vacuum drying in place, then discharges the finished dry powder. Slurry is charged onto a filter plate at the bottom of the vessel; pressure or vacuum drives the liquor through; the cake is washed, then dried under vacuum with a heated jacket while an agitator stirs it; and finally the dry product is discharged through a side or bottom valve. Because the material never leaves the vessel between these steps, an agitated nutsche filter dryer removes the transfers that are the main source of operator exposure and product loss in a conventional filtration-and-drying suite.
Working Principle
Charge. Slurry is charged into the closed vessel onto the filter plate.
Filtration. Nitrogen pressure or vacuum drives the mother liquor through the filter medium, leaving a cake on the plate. 3) Washing. Wash liquid is applied and the agitator reslurries or rewashes the cake, displacing mother liquor and soluble impurities.
Filtration again. The wash liquor is filtered off in the same way.
Vacuum drying. The jacket is heated, vacuum is applied and the agitator keeps turning to expose fresh surface, so the cake dries evenly without the crusting that a static bed suffers.
Discharge. The dry powder is discharged through a valve, usually with the agitator moving it out, into a closed receiver.
Key Features
- Four steps, one vessel - filtration, washing, drying and discharge happen in place, so the product is never transferred between machines.
- Greatly reduced operator exposure - the enclosed design is central to handling potent, toxic or sensitising compounds safely.
- Higher yield - no transfers means no losses on floors, in trays or in transfer lines, and no hold-up in intermediate containers.
- Even, fast drying - an agitator exposes fresh surface continuously, so drying is quicker and more uniform than in a static vacuum tray dryer.
- GMP-ready construction - 304 or 316L contact parts, polished surfaces, CIP and SIP capability, and full documentation for validation.
- Scales from pilot to production - vessel diameters up to 4600 mm, with the same operating principle at every size so scale-up is predictable.
Typical Applications
An ANFD is specified wherever a filtration-and-drying step has to be contained, where product loss matters, or where the material is potent enough that operator exposure must be designed out:
· Active pharmaceutical ingredients (API)· high-potency compounds· agrochemical intermediates· fine chemicals· dye and pigment· specialty chemicals with solvent wash· food and nutraceutical ingredients· pilot and scale-up studies
Selection Guide
A three-in-one vessel and a separate filter plus dryer suite achieve the same chemistry. The difference is containment, yield and footprint:
|
Criteria |
ANFD three-in-one |
Filter centrifuge plus tray dryer |
Filter press plus tray dryer |
|
Product transfers |
None - one vessel |
Several open transfers |
Several, including cake handling |
|
Operator exposure |
Very low, enclosed |
High - trays, cake handling |
High |
|
Yield |
Highest |
Lower - losses at each transfer |
Lower |
|
Drying uniformity |
Good - agitated bed |
Variable across trays |
Variable |
|
Footprint |
One vessel |
Two or more machines plus trays |
Two plus trays |
|
Validation |
Straightforward - one closed system |
Complex - multiple steps to validate |
Complex |
|
Best suited to |
Potent APIs and high-value products |
Simple, low-hazard products |
Large simple slurry volumes |
Choose the ANFD when containment, yield and validation simplicity justify the higher capital cost - which is the case for most modern API and high-potency processes. For simple, low-hazard products in large volumes, a separate filter and dryer can still be the cheaper route, and we will say so.
Technical Specifications
|
Model |
Vessel dia. (mm) |
Filter area (m²) |
Vessel volume (L) |
Working pressure |
Working temperature |
Agitator drive (kW) |
|
ANFD800 |
800 |
0.5 |
300 |
–0.1 / +0.3 MPa |
Up to 150 °C |
5.5 |
|
ANFD1200 |
1,200 |
1.1 |
900 |
–0.1 / +0.3 MPa |
Up to 150 °C |
11 |
|
ANFD1600 |
1,600 |
2.0 |
2,000 |
–0.1 / +0.3 MPa |
Up to 150 °C |
18.5 |
|
ANFD2000 |
2,000 |
3.1 |
4,000 |
–0.1 / +0.3 MPa |
Up to 150 °C |
30 |
|
ANFD2600 |
2,600 |
5.3 |
8,000 |
–0.1 / +0.3 MPa |
Up to 150 °C |
45 |
|
ANFD4600 |
4,600 |
16.6 |
40,000 |
–0.1 / +0.3 MPa |
Up to 150 °C |
90 |
Customization & Options
Contact parts in 304, 316L, duplex or Hastelloy; polished and electropolished surfaces to an agreed Ra; Hastelloy or PTFE-lined versions for aggressive chemistry; CIP spray balls and SIP capability; bottom discharge valve or side discharge for the discharge behaviour of your product; filtered nitrogen and pressure or vacuum operation; jacket heating with temperature control; load cells for charge and yield measurement; ATEX-rated execution; full documentation set for validation.
FAQ
Q: How does the ANFD dry the cake better than a tray dryer?
Because the agitator keeps turning. In a static tray dryer the surface dries first and forms a crust that slows the escape of vapor from below, so drying is slow and uneven across the tray. In an ANFD the agitator continuously exposes fresh wet surface to the vacuum, so drying is faster and the batch is uniform - which also shortens the cycle.
Q: What is the practical limit on vessel size?
We supply vessels up to 4600 mm diameter. The limit is not the principle but the mechanical design of the agitator and discharge, together with the physical handling of very large filter plates. The same operating concept holds at every size, which is what makes scale-up from a pilot vessel predictable.
Q: Can it handle solvents and flammable products?
Yes, in the ATEX-rated execution with filtered nitrogen, inerting, flameproof instrumentation and proper grounding. Solvent-wet cakes are in fact a common application, because the drying step is exactly where solvent vapor is released and containment matters most.
Q: How is the finished product discharged?
Through a bottom valve, or through a side discharge port where the product flows poorly. The agitator is used to move the dry powder toward the outlet, so discharge is positive rather than relying on gravity alone. On contained versions discharge is into a closed receiver or a glovebox interface.
Q: What documentation is provided for validation?
The machine is supplied with material certificates for contact parts, surface finish records, weld documentation, instrument calibration certificates and the operating and maintenance manual. Additional documentation to match your own validation protocol can be agreed at order stage.
Why Jiangsu Shengli Centrifuge
Behind this machine is Jiangsu Shengli Centrifuge Manufacturing Co., Ltd.: a 20,000+ m² manufacturing plant, ISO 9001, ISO 14001 and ISO 45001 certification, CE marking, more than 30 patents and installations in over 30 countries. Rotor balancing, wear-facing and final testing are done in house, so the machine that arrives on site is the machine that was measured on the balancing machine, and the report to prove it travels with it.

Request a Quote or a Free Separation Test
Talk to our engineers with your material data in hand. Send a sample, tell us the throughput you need and the specification you have to meet, and we will come back with a measured result, a recommended model and the operating settings that produced it - not simply the largest machine in the range.
Hot Tags: agitated nutsche filter dryer, China agitated nutsche filter dryer manufacturers, suppliers, factory


